Sock Printer User Manual: Detailed introduction in eight parts

Socks Printer User Manual

Detailed Socks Printer Operation Manual

Table Of Contents

1.Preface 2.Installation of the socks printer 3.Operation guide 4.Maintenance and maintenance 5.Troubleshooting 6.Safety instructions 7.Appendix 8.Contact information

1.Preface

Colorido socks printer is to print various patterns on socks to meet the growing demand of users for personalized products. Compared with traditional digital printing technology, the sock printer can provide a faster and more flexible production solution, which fully meets the market demand. In addition, the production process of the sock printer is simple and efficient, and it realizes on-demand printing and supports a variety of printing materials, which expands the user's choice range.

Socks printer user manual mainly provides users with detailed operating instructions and technical support, allowing users to master the use of the printer as soon as possible.

2.Installation Of The Socks PrinterUnpacking and Inspection

We will do relevant debugging before exporting the socks printer. The machine will be shipped complete. When the customer receives the equipment, they only need to install a small part of the accessories and power it on to use.

When you receive the device, you need to check the accessories. If you are missing any accessories, please contact the salesperson in time.

Installation Steps

1. Check the appearance of the wooden box: Check whether the wooden box is damaged after receiving the sock printer.

2. Unpacking: Remove the nails on the wooden box and remove the wooden board.

3. Check the equipment: Check whether the paint of the sock printer is scratched and whether the equipment is bumped.

4. Horizontal placement: Place the equipment on a horizontal ground for the next step of installation and debugging.

5. Release the head: Untie the cable tie that fixes the head so that the head can move.

6. Power on: Power on to check whether the machine is working properly.

7. Install accessories: Install equipment accessories after the sock printer operates normally.

8. Empty printing: After installing the accessories, open the printing software to import the picture for empty printing to see if the printing action is normal.

9. Install the nozzle: Install the nozzle and ink after the printing action is normal.

10. Debugging: After the firmware installation is completed, perform software parameter debugging.

Find the material USB flash drive we provided, and find the printer installation video in it. It contains detailed operation steps. Follow the video step by step.

3.Operation GuideBasic Operation

Detailed introduction to the printing software interface

File import location

In this interface, you can see the pictures you need to print. Select the pictures you need to print and double-click to import them.

Printing

Import the printed image into the printing software and print it. Double-click the image to modify the number of prints required.

Set up

Perform some general settings for printing, including printing speed, nozzle selection, and inkjet mode.

Calibration

On the left, these calibrations can help us print clearer patterns.

Voltage

Here you can set the voltage of the nozzle. We will set it before leaving the factory, and users basically do not need to change it.

Cleaning

Here you can adjust the intensity of the cleaning

Advanced

Enter the factory mode to set more printing parameters. Users basically do not need to set them here.

Toolbar

Some common operations can be performed in the toolbar

4.Maintenance And Maintenance

Daily Maintenance

Daily maintenance of the sock printer. After a day of printing, you need to clean up unnecessary items on the device. Move the small head out to check if there are fibers from the socks stuck on the bottom of the head. If there are, you need to clean them in time. Check if the waste ink in the waste ink bottle needs to be poured out. Turn off the power and check whether the nozzle is closed with the ink stack.Check whether the ink in the large ink cartridge needs to be refilled.

Regular Inspection

The belts, gears, ink stacks, and guide rails of the sock printer need to be checked regularly. Lubricating oil needs to be applied to the gears and guide rails to prevent the head from wearing out during high-speed movement.

Recommendations For Not Using The Socks Printer For A Long Time

If the machine is not used for a long time during the off-season, you need to pour pure water on the ink stack to keep the nozzle moist to prevent clogging. You need to print pictures and test strips every three days to check the status of the nozzle.

5.Maintenance And Troubleshooting

1. The print test strip is broken Solution: Click Clean to clean the print head. If it still doesn't work, click Load Ink, let it sit for a few minutes, and then click Clean.

2. The print seam is very sharp Solution: Increase the feathering value

3. The print pattern is fuzzy Solution: Click the test calibration chart to check if the value is biased.

If you encounter other problems that cannot be solved, please contact the engineer in time

6.Safety Tips Operation Instructions

The carriage is the core component of the sock printer. During the printing process, the socks need to be kept flat to prevent the nozzle from being scratched during the printing process, causing unnecessary economic losses. If you encounter special problems, there are emergency stop buttons on both sides of the machine, which can be pressed immediately and the device will be powered off immediately.

7.Appendix

Technical Parameters

8.Contact Information

E-Mail Joan@coloridoprinter.com

Telephone 0574-87237965

WhatsApp +86 13967852601

Media Contact
Company Name: Ningbo Haishu Colorido Digital Technology Co., Ltd.
Email: Send Email
Phone: +86 13967852601
Address:NO.106 Yuji Road, Jiaochuan Street, Zhenhai District
City: Ningbo
State: Zhejiang 315221
Country: China
Website: https://www.coloridoprinting.com/